- Download Renault Trucks NG3 NG10 calculator v0.1
$26.00Add to cart
- DOWNLOAD NEXIQ eTechnician 2.1.7657.26963 + Patch 2020
$58.00Add to cart
- JPRO software download 2023 1.2 off-highway – on-highway
$96.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
The aftertreatment particulate matter sensor is a smart device and communicates with the engine control module (ECM) via the J1939 data link. The aftertreatment particulate matter sensor performs internal diagnostics and reports malfunctions back to the primary ECM using the J1939 data link. The particulate matter sensor is permanently attached to the particulate matter control module. They are serviced as a single component and can not be replaced individually. The aftertreatment particulate matter sensor is used to measure the soot emissions at the outlet of the aftertreatment system.
Component Location
The aftertreatment particulate matter sensor location can vary depending on engine application. It is usually located in the exhaust system at the outlet of the selective catalytic reduction (SCR) catalyst.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the engine is running.
Conditions for Setting the Fault Codes
The Engine Control Module (ECM) lost communication with the aftertreatment particulate matter sensor via the J1939 data link.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or Malfunction Indicator Lamp (MIL) after the diagnostic fails on two consecutive trips.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for 1 minute.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes for this fault include:
Sensor supply wire open or shorted to ground
Sensor return wire open.
An open or short circuit in the SAE J1939 datalink circuit
Malfunctioning aftertreatment particulate matter sensor
For intermittent power supply and data link communication issues with aftertreatment components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing, or intermittent connections.
Possible Cause:
1) ECM calibration
Related
Tags: , 1, 2018, 5835, 6688, 9, Abnormal, Aftertreatment, CM2350, Code, Cummins, Fault, FMI, Newer, Particulate, PID, Rate, Sensor-, SPN, Update, X119B, X12
Reviews
There are no reviews yet.
Be the first to review “Cummins X12 CM2350 X119B (2018 & Newer) Fault Code: 6688 PID: SPN: 5835 FMI: 9 Aftertreatment 1 Particulate Sensor- Abnormal Update Rate”
Categories Cumminz, DTC TRUCKS, Tags , 1, 2018, 5835, 6688, 9, Abnormal, Aftertreatment, CM2350, Code, Cummins, Fault, FMI, Newer, Particulate, PID, Rate, Sensor-, SPN, Update, X119B, X12
- See AlsoCummins X12 CM2350 X119B (2018 & Newer) Fault Code: 6688 PID: SPN: 5835 FMI: 9 Aftertreatment 1 Particulate Sensor- Abnormal Update Rate - EcuForce TruckCummins ISB6.7 CM2350 (2013-17) Fault Code: 4143 PID: SPN: 5835 FMI: 3 Aftertreatment 1 Particulate Sensor Circuit- Voltage Above Normal Or Shorted To High Source - EcuForce TruckCummins ISB6.7 CM2350 (2013-17) Fault Code: 5837 PID: SPN: 5835 FMI: 21 Aftertreatment 1 Particulate Sensor - Data Not Rational - Drifted Low. An In-range Low Failure Has Been Detected. - EcuForce TruckCummins X15 CM2450 X124B (2018 & Newer) Fault Code: 4143 PID: SPN: 5835 FMI: 3 Aftertreatment 1 Particulate Sensor Circuit- Voltage Above Normal Or Shorted To High Source - EcuForce TruckDOWNLOAD Meritor Wabco Tool Box 12.12
$40.00Add to cart
- DOWNLOAD NEXIQ eTechnician 2.1.7657.26963 + Patch 2020
$58.00Add to cart
- DOWNLOAD CNH EST 9.8 ENGINEERING
$100.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
DTC TRUCKSPACCARPX-9 CM2350 (2013-17)
PACCAR PX-9 CM2350 (2013-17) Fault Code:1924 PID:SID 334 SPN:3482 FMI:4 Aftertreatment Fuel Shutoff Valve Circuit – Voltage Below Normal or Shorted to Low Source
Quick View
Add to wishlist
CompareAdd to cart
DTC TRUCKSPACCARPX-9 CM2350 (2013-17)
PACCAR PX-9 CM2350 (2013-17) Fault Code1927 PID:SID 332 SPN:3480 FMI:3 Aftertreatment Fuel Pressure Sensor Circuit – Voltage Above Normal or Shorted to High Source
Quick View
Add to wishlist
CompareAdd to cart
DTC TRUCKSPACCARPX-9 CM2350 (2013-17)
PACCAR PX-9 CM2350 (2013-17) Fault Code:195 PID:111 SPN:111 FMI:3 Coolant Level Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source
Quick View
Add to wishlist
CompareAdd to cart
DTC TRUCKSPACCARPX-9 CM2350 (2013-17)
PACCAR PX-9 CM2350 (2013-17) Fault Code:1963 PID:SID 332 SPN:3482 FMI:7 Aftertreatment Fuel Shutoff Valve – Mechanical System Not Responding or Out of Adjustment
Quick View
Add to wishlist
CompareAdd to cart
DTC TRUCKSPACCARPX-9 CM2350 (2013-17)
PACCAR PX-9 CM2350 (2013-17) Fault Code:196-2 PID:111 SPN:111 FMI:4 Coolant Level Sensor 1 Circuit – Voltage Below Normal or Shorted to Low Source
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
CAT
DOWNLOAD Caterpillar ET 2022A Electronic Technician + Factory Password (1PC)$96.00Add to cart
DETROIT
SERVICE MANUAL DETROIT Earings – Technicians Guide$45.00Add to cart
CARRIE
SERVICE MANUAL Carrie Integra 40 50S$45.00Add to cart
INTERNATIONAL ENGINES
SERVICE MANUAL International Engines DT466 (2004-2006)$45.00Add to cart
EATON
SERVICE MANUAL EATON UltraShift PLUS$45.00Add to cart
MACK
SERVICE MANUAL Mack MP10$45.00Add to cart
INTERNATIONAL ENGINES
$45.00Add to cart
TRUCK MANUALS
VOLVOUU D13 ENGINE service manual$45.00Add to cart